nunomiguelneto Posted December 4, 2006 Report Share Posted December 4, 2006 Bom dia! Caros amigos, venho por-vos o seguinte problema... Na minha faculdade usa-se a versão educacional do AutoCad, acontece que esta versão por ser free, deixa a sua marca em todas as impressões de desenhos com um banner stamp com os dizeres: "Produced by AutoCad Educational Project" esta marca aparece nos limites da folha. Como em casa tenho AutoCad licenciado, e este banner transfere-se automaticamente para todo o ficheiro, em que se efectue cópia de qualquer componente do desenho destes "ficheiros educacionais" fico com outros ficheiros afectados por este banner. Vinha perguntar se alguem conhece maneira de desactivar e/ou remover esta situação, que tanto transtorno tem causado a mim e aos meus colegas. Já tentei algumas soluções para o problema tais como: gravar o ficheiro depois de manipulado no cad normal; guardar o ficheiro numa versão mais antiga; mas a unica solução parece ser mesmo a impressao numa folha maior, o que me causa alguma despesa pois pussuo impressora A3 em casa, e assim tenho que me deslocar a lojas de impressao para imprimir em páginas de maior formato. Aguardo resposta Abraço Arquitectónico a todos http://nunomiguelneto.tumblr.com/http://canaisdoneto.wordpress.com Link to comment Share on other sites More sharing options...
Rodrigues Posted December 12, 2006 Report Share Posted December 12, 2006 Em resposta à tua dúvida, eu tive esse problema à uns meses atrás e na altura consegui resolver, apesar de não me lembrar muito bem, penso que gravei o ficheiro na extensão DXF. Depois abri esse ficheiro "nome".dxf. e fiz um save as na extensão dwg. penso que foi assim mas n tenho bem a certeza mas exprimenta e logo verás, ou tenta mesmo imprimei em dxf. Abraço Link to comment Share on other sites More sharing options...
3CPO Posted December 12, 2006 Report Share Posted December 12, 2006 Issue: When you plot a drawing that was created in or that contains drawing data that was created in the Educational (Student and Faculty) version of AutoCAD® or AutoCAD-based software, the following plot stamp or watermark appears in the plot: For Educational Use OnlySolution: There is no way to circumvent the plot stamp. This is as designed to discourage the commercial use of an educational version of an AutoCAD product. Autodesk sells educational versions of software on the premise that the software will be used for educational purposes only. This can also occur when using blocks or other components of drawings that have been created or modified in an Educational version. This includes layers, blocks, layouts, and so on. ALSO if you have a commercial drawing that has an educational stamp: We cannot assist you in this forum. This is a PEER TO PEER support group. Fonte: http://discussion.autodesk.com Pesquisando um pouco mais, chega-se a foruns Brasileiros que propõem uma solução ao problema:A unica forma que eu descobri, pesquisando na rede, foi: 1 - Salve seu arquivo em DXF e feche. 2 - Abri em DXF e salve com DWG e feche novamente. 3 - Abri novamente como DWG e pronto. Abraços :p Link to comment Share on other sites More sharing options...
3CPO Posted December 12, 2006 Report Share Posted December 12, 2006 When you plot a drawing that was created in, or that contains drawing data that was created using an Educational (Student and Faculty) version of AutoCAD, a plot stamp on all four sides of the sheet appears. HOWEVER, there is a fix. Try this: Download a free trial version of ProgeCAD from:http://www.progecad.com ProgeCAD LT 2006 is free CAD software that uses “DWG” native file format. 1. Once installed, open the contaminated file using ProgeCAD and save it. The file will be saved in DWG format. 2. Then re-open the file using AutoCAD. The Plot stamps and warning should be gone. NOTE: You can try to save file as .dxf and re-open in AutoCAD. Source: Unverified. Fonte: http://cben.net/ Link to comment Share on other sites More sharing options...
Nemezis Posted December 13, 2006 Report Share Posted December 13, 2006 Era isso mesmo que eu fazia quando trabalhava na reprografia da faculdade resulta muito bem, com excepção dos ficheiros com elementos específicos do formato DWG (alguns tipos de hatches com gradientes, etc..). Mas resulta, o banner desaparece :p Link to comment Share on other sites More sharing options...
Recommended Posts
Please sign in to comment
You will be able to leave a comment after signing in
Sign In Now